Bed Linen Cut Plan & Fabric Consumption Calculator

The formula

This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.

How the result is derived

Step by step, from the values you type to the figure on screen.

1. The 10 inputs are read from the form on every keystroke: Finished Length, Finished Width, Fitted Pocket Depth, Hem, Length Direction, Hem, Width Direction, Residual Shrinkage, Cutting and Rejects, Usable Fabric Width, Fabric Weight and Fabric Price.
2. Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
3. The validated values are substituted into the expression above, which resolves Fabric per Piece together with every supporting figure in one pass — no value is carried over from a previous entry.
4. The supporting outputs — Cut Length, Cut Width, Pieces Across the Width, Width Used, Selvedge Strip Wasted, Fabric per Piece, Fabric Cost per Piece, Cost of the Wasted Strip and Cut Width That Would Gain a Piece — come from the same pass, so they always describe the same case as the headline figure.
5. Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.

What each input means

Where to read each value on the floor, the unit it must be in, and the range the tool accepts.

What the tool returns

The headline figure and every supporting value it is built from.

Worked example

The tool loads with this case already solved — the Fabric per Piece shown above is its answer. Change one value and the difference from this baseline is the sensitivity of the result to that variable.

How to use it

1. Work through the input groups in order — The Finished Piece, Making Allowances and The Roll. The defaults are a realistic case, so you can change one value at a time and watch what moves.
2. There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
3. Read Fabric per Piece in the dark results panel — that is the headline figure, expressed in m.
4. Check the supporting rows underneath (Cut Length, Cut Width, Pieces Across the Width, Width Used, Selvedge Strip Wasted, Fabric per Piece, Fabric Cost per Piece, Cost of the Wasted Strip and Cut Width That Would Gain a Piece) before acting on the headline — they are where an implausible input usually shows itself first.
5. Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.

Where this is used

• Process planning — establishing Fabric per Piece before a trial is booked, so machine time and material in Apparel Manufacturing & Garmenting are committed against a calculated figure rather than an estimate.
• Costing and quotation — Fabric per Piece is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
• Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Finished Length) shows how much of the gap in Fabric per Piece each variable explains.
• Teaching and study — the accepted ranges bracket normal Apparel Manufacturing & Garmenting practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.

Assumptions and limits

• One piece type at a time. A set is the sum of its parts and each part has its own cut width, so a flat sheet, a fitted sheet and a pair of pillowcases are four runs of this sheet rather than one. Where no whole piece fits across the usable width, the cut width itself is the consumption and the strip wasted is zero — that is a roll too narrow for the specification rather than an efficient cut.
• Every input is bounded to the range normal practice occupies (Finished Length 10 to 500 cm, Finished Width 10 to 400 cm and Fitted Pocket Depth 0 to 80 cm, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
• The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
• Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.

Questions people ask