Jump to a calculator 671 tools
Jacquard
Jacquard Hook Capacity & Pattern Repeat Limit Tool
Hooks limit the repeat across the cloth; pattern memory limits it up the cloth. Designers hit whichever is smaller, and it is rarely the one they were told about.
Design Repeat Width
— cm
Widest repeat the chosen layout allows
Capacity Check
- Total Ends in Cloth
- — no.
- Ends per Repeat
- — no.
- Hook Utilisation
- — %
- Spare Hooks
- — no.
- Maximum Repeat Height
- — cm
A negative spare-hook figure means the cloth needs more ends than the machine can control — reduce the ends per cm, narrow the cloth, or move to a larger jacquard.
Using this calculator
About the Jacquard Hook Capacity & Pattern Repeat Limit Tool
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
totalEnds = endsPerCm x fabricWidthEach end on an electronic jacquard needs its own hook unless the harness ties ends together.
repeatWidth = totalEnds / repeatsAcross / endsPerCmEqual to fabric width divided by the repeats across.
maxRepeatHeight = cardCapacity / picksPerCm| Symbol | Stands for | Unit |
|---|---|---|
hooks | Hooks Available | no. |
cardCapacity | Pattern Memory | picks |
endsPerCm | Ends per cm | ends/cm |
fabricWidth | Fabric Width | cm |
picksPerCm | Picks per cm | picks/cm |
repeatsAcross | Design Repeats Across the Width | no. |
repeatWidth | Design Repeat Width | cm |
totalEnds | Total Ends in Cloth | no. |
endsPerRepeat | Ends per Repeat | no. |
hookUtilisation | Hook Utilisation | % |
spareHooks | Spare Hooks | no. |
maxRepeatHeight | Maximum Repeat Height | cm |
How the result is derived
Step by step, from the values you type to the figure on screen.
- The 6 inputs are read from the form on every keystroke: Hooks Available, Pattern Memory, Ends per cm, Fabric Width, Picks per cm and Design Repeats Across the Width.
- Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
- The validated values are substituted into the expression above, which resolves Design Repeat Width together with every supporting figure in one pass — no value is carried over from a previous entry.
- The supporting outputs — Total Ends in Cloth, Ends per Repeat, Hook Utilisation, Spare Hooks and Maximum Repeat Height — come from the same pass, so they always describe the same case as the headline figure.
- Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Hooks Available | no. | 100 to 40000 no. | 6144 | |
| Pattern Memory | picks | 100 to 500000 picks | 20000 | |
| Ends per cm | ends/cm | 1 to 300 ends/cm | 40 | |
| Fabric Width | cm | 1 to 500 cm | 150 | |
| Picks per cm | picks/cm | 1 to 300 picks/cm | 30 | |
| Design Repeats Across the Width | no. | 1 to 50 no. | 4 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Design Repeat Width (headline result) | cm | Widest repeat the chosen layout allows |
| Total Ends in Cloth | no. | |
| Ends per Repeat | no. | |
| Hook Utilisation | % | |
| Spare Hooks | no. | |
| Maximum Repeat Height | cm |
Worked example
Given
- Jacquard
- 6,144 hooks, 20,000-pick pattern memory
- Cloth
- 40 ends/cm x 150 cm, 30 picks/cm
- Layout
- 4 repeats across
Substituting
totalEnds = 40 x 150 = 6,000; 6,000 / 6,144 = 97.7 %; spare = 144endsPerRepeat = 6,000 / 4 = 1,500; width = 1,500 / 40 = 37.5 cmmaxRepeatHeight = 20,000 / 30 = 666.7 cmAnswer
- Ends
- 6,000 (97.7% of hooks, 144 spare)
- Repeat width
- 37.5 cm, 1,500 ends
- Repeat height limit
- 666.7 cm
At 42 ends/cm the cloth needs 6,300 ends, 156 more than the machine has.
How to use it
- Work through the input groups in order — Machine and Cloth. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Design Repeat Width in the dark results panel — that is the headline figure, expressed in cm.
- Check the supporting rows underneath (Total Ends in Cloth, Ends per Repeat, Hook Utilisation, Spare Hooks and Maximum Repeat Height) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Process planning — establishing Design Repeat Width before a trial is booked, so machine time and material in Narrow Fabrics, Tapes & 3D Weaving are committed against a calculated figure rather than an estimate.
- Costing and quotation — Design Repeat Width is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
- Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Hooks Available) shows how much of the gap in Design Repeat Width each variable explains.
- Teaching and study — the accepted ranges bracket normal Narrow Fabrics, Tapes & 3D Weaving practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.
Reading the result
Typical bands and what each one is telling you.
| Value | What it indicates |
|---|---|
| Spare hooks negative | The cloth needs more ends than the jacquard controls. Reduce the sett, narrow the cloth, tie ends together in the harness, or use a larger jacquard. |
| Fewer repeats across | Wider, more detailed repeats, since the hooks are shared by fewer copies of the design. One repeat across uses every hook for one design. |
| Repeat height limit tight | The pattern memory, not the hooks, limits the design length. Fewer picks per cm or more memory raises it. |
Assumptions and limits
- A negative spare-hook figure means the cloth needs more ends than the machine can control — reduce the ends per cm, narrow the cloth, or move to a larger jacquard.
- Every input is bounded to the range normal practice occupies (Hooks Available 100 to 40000 no., Pattern Memory 100 to 500000 picks and Ends per cm 1 to 300 ends/cm, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
Questions people ask
What if the harness ties several ends to one hook?
Then each hook controls that many ends, and the hook count needed falls in proportion. Enter the hooks the design really uses.
Do selvedges need hooks?
Often they are woven by separate shafts or a separate device. If your selvedges are on the jacquard, add their ends to the cloth width.
Is the repeat height limit a hard limit?
It is the length the pattern memory holds at this pick density. Some controllers chain patterns, so check what yours supports.