Jump to a calculator 671 tools
Ring Spinning
Spindle Wharve, Tape Speed & Slippage Calculator
Slip is not a maintenance abstraction. A two percent loss on the tape is two percent of the twist the yarn was sold with.
Tape Slip
— %
Spindle speed lost between tape and wharve
Drive Chain
- Tape Surface Speed
- — m/min
- Theoretical Spindle Speed
- — rpm
- Spindle Speed Lost
- — rpm
- Design Twist
- — TPM
- Twist Shortfall
- — TPM
Check slip across the frame, not on one spindle: a rising spread between the drive end and the far end is the tape tensioner, while a uniform loss is usually the tape itself.
Using this calculator
About the Spindle Wharve, Tape Speed & Slippage Calculator
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
slipPercent = f( cylinderDiameter, cylinderSpeed, wharveDiameter, measuredSpindleSpeed, deliverySpeed )Each input feeds the expression evaluated in the browser; the symbol table below names every term and its unit.
| Symbol | Stands for | Unit |
|---|---|---|
cylinderDiameter | Drive Cylinder Diameter | mm |
cylinderSpeed | Drive Cylinder Speed | rpm |
wharveDiameter | Spindle Wharve Diameter | mm |
measuredSpindleSpeed | Measured Spindle Speed | rpm |
deliverySpeed | Front Roller Delivery | m/min |
slipPercent | Tape Slip | % |
tapeSpeed | Tape Surface Speed | m/min |
theoreticalSpeed | Theoretical Spindle Speed | rpm |
speedLoss | Spindle Speed Lost | rpm |
designTwist | Design Twist | TPM |
twistShortfall | Twist Shortfall | TPM |
How the result is derived
Step by step, from the values you type to the figure on screen.
- The 5 inputs are read from the form on every keystroke: Drive Cylinder Diameter, Drive Cylinder Speed, Spindle Wharve Diameter, Measured Spindle Speed and Front Roller Delivery.
- Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
- The validated values are substituted into the expression above, which resolves Tape Slip together with every supporting figure in one pass — no value is carried over from a previous entry.
- The supporting outputs — Tape Surface Speed, Theoretical Spindle Speed, Spindle Speed Lost, Design Twist and Twist Shortfall — come from the same pass, so they always describe the same case as the headline figure.
- Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Drive Cylinder Diameter | mm | 50 to 800 mm | 250 | |
| Drive Cylinder Speed | rpm | 100 to 5000 rpm | 1500 | |
| Spindle Wharve Diameter | mm | 15 to 40 mm | 21 | |
| Measured Spindle Speed | rpm | 1000 to 30000 rpm | 17500 | |
| Front Roller Delivery | m/min | 1 to 60 m/min | 18 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Tape Slip (headline result) | % | Spindle speed lost between tape and wharve |
| Tape Surface Speed | m/min | |
| Theoretical Spindle Speed | rpm | |
| Spindle Speed Lost | rpm | |
| Design Twist | TPM | |
| Twist Shortfall | TPM |
Worked example
Given
- Drive Cylinder Diameter
- 250 mm
- Drive Cylinder Speed
- 1500 rpm
- Spindle Wharve Diameter
- 21 mm
- Measured Spindle Speed
- 17500 rpm
- Front Roller Delivery
- 18 m/min
The tool loads with this case already solved — the Tape Slip shown above is its answer. Change one value and the difference from this baseline is the sensitivity of the result to that variable.
How to use it
- Work through the input groups in order — Drive and Measured. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Tape Slip in the dark results panel — that is the headline figure, expressed in %.
- Check the supporting rows underneath (Tape Surface Speed, Theoretical Spindle Speed, Spindle Speed Lost, Design Twist and Twist Shortfall) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Process planning — establishing Tape Slip before a trial is booked, so machine time and material in Advanced Spinning, Texturizing & Twisting are committed against a calculated figure rather than an estimate.
- Costing and quotation — Tape Slip is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
- Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Drive Cylinder Diameter) shows how much of the gap in Tape Slip each variable explains.
- Teaching and study — the accepted ranges bracket normal Advanced Spinning, Texturizing & Twisting practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.
Assumptions and limits
- Check slip across the frame, not on one spindle: a rising spread between the drive end and the far end is the tape tensioner, while a uniform loss is usually the tape itself.
- Every input is bounded to the range normal practice occupies (Drive Cylinder Diameter 50 to 800 mm, Drive Cylinder Speed 100 to 5000 rpm and Spindle Wharve Diameter 15 to 40 mm, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
On this site
Articles that explain what this tool calculates.
Questions people ask
What do I need to know before using the Spindle Wharve, Tape Speed & Slippage Calculator?
Have these to hand: Drive Cylinder Diameter, Drive Cylinder Speed, Spindle Wharve Diameter, Measured Spindle Speed and Front Roller Delivery. With those entered, the tool returns Tape Slip immediately.
What exactly is Tape Slip?
Spindle speed lost between tape and wharve. It is reported in %. It is derived from Drive Cylinder Diameter, Drive Cylinder Speed, Spindle Wharve Diameter, Measured Spindle Speed and Front Roller Delivery, and is the figure the rest of the Advanced Spinning, Texturizing & Twisting calculation is built around.
Which units does this calculator expect?
Enter Drive Cylinder Diameter in mm, Drive Cylinder Speed in rpm, Spindle Wharve Diameter in mm, Measured Spindle Speed in rpm and Front Roller Delivery in m/min. Mixing unit systems is the most common cause of a result that looks an order of magnitude wrong — convert before typing, not after reading.
What are the other figures under the main result?
They are the intermediate quantities the calculation passes through: Tape Surface Speed, Theoretical Spindle Speed, Spindle Speed Lost, Design Twist and Twist Shortfall. They are shown because a headline number nobody can trace is a number nobody trusts — checking them against your own expectation is the fastest way to confirm the inputs were read as you intended.
Can I rely on this for a production decision?
Check slip across the frame, not on one spindle: a rising spread between the drive end and the far end is the tape tensioner, while a uniform loss is usually the tape itself. Treat the output as an engineering estimate that narrows the trial window, not as a substitute for the trial.