Jump to a calculator 671 tools
Warp Knitting
Warp Knit Rack Length & Two-Bar Run-in Ratio Calculator
The runner ratio between the bars is the fabric. Change it and you have a different cloth at the same weight, gauge and yarn.
Fabric Areal Weight
— g/m²
Both guide bars together, loom-state
Bar Balance
- Front-to-Back Runner Ratio
- — ×
- Front Bar Stitch Length
- — mm/course
- Back Bar Stitch Length
- — mm/course
- Fabric Produced per Rack
- — cm
- Combined Run-in
- — mm/rack
Loom-state weight before relaxation and heat setting. A ratio far from the machine builder's window for the lapping usually shows up as barré or curling long before it shows up in the weight.
Using this calculator
About the Warp Knit Rack Length & Two-Bar Run-in Ratio Calculator
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
fabricGsm = f( frontBarRunner, backBarRunner, frontYarnDtex, backYarnDtex, machineGauge, coursesPerCm )Each input feeds the expression evaluated in the browser; the symbol table below names every term and its unit.
| Symbol | Stands for | Unit |
|---|---|---|
frontBarRunner | Front Bar Runner | mm/rack |
backBarRunner | Back Bar Runner | mm/rack |
frontYarnDtex | Front Bar Yarn | dtex |
backYarnDtex | Back Bar Yarn | dtex |
machineGauge | Machine Gauge | needles/inch |
coursesPerCm | Course Density | courses/cm |
fabricGsm | Fabric Areal Weight | g/m² |
runnerRatio | Front-to-Back Runner Ratio | × |
frontStitchLength | Front Bar Stitch Length | mm/course |
backStitchLength | Back Bar Stitch Length | mm/course |
fabricPerRack | Fabric Produced per Rack | cm |
totalRunner | Combined Run-in | mm/rack |
How the result is derived
Step by step, from the values you type to the figure on screen.
- The 6 inputs are read from the form on every keystroke: Front Bar Runner, Back Bar Runner, Front Bar Yarn, Back Bar Yarn, Machine Gauge and Course Density.
- Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
- The validated values are substituted into the expression above, which resolves Fabric Areal Weight together with every supporting figure in one pass — no value is carried over from a previous entry.
- The supporting outputs — Front-to-Back Runner Ratio, Front Bar Stitch Length, Back Bar Stitch Length, Fabric Produced per Rack and Combined Run-in — come from the same pass, so they always describe the same case as the headline figure.
- Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Front Bar Runner | mm/rack | 100 to 10000 mm/rack | 1450 | |
| Back Bar Runner | mm/rack | 100 to 10000 mm/rack | 1100 | |
| Front Bar Yarn | dtex | 10 to 5000 dtex | 78 | |
| Back Bar Yarn | dtex | 10 to 5000 dtex | 44 | |
| Machine Gauge | needles/inch | 6 to 44 needles/inch | 28 | |
| Course Density | courses/cm | 2 to 60 courses/cm | 12 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Fabric Areal Weight (headline result) | g/m² | Both guide bars together, loom-state |
| Front-to-Back Runner Ratio | × | |
| Front Bar Stitch Length | mm/course | |
| Back Bar Stitch Length | mm/course | |
| Fabric Produced per Rack | cm | |
| Combined Run-in | mm/rack |
Worked example
Given
- Front Bar Runner
- 1450 mm/rack
- Back Bar Runner
- 1100 mm/rack
- Front Bar Yarn
- 78 dtex
- Back Bar Yarn
- 44 dtex
- Machine Gauge
- 28 needles/inch
- Course Density
- 12 courses/cm
The tool loads with this case already solved — the Fabric Areal Weight shown above is its answer. Change one value and the difference from this baseline is the sensitivity of the result to that variable.
How to use it
- Work through the input groups in order — Run-in per Rack, Yarn and Machine & Fabric. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Fabric Areal Weight in the dark results panel — that is the headline figure, expressed in g/m².
- Check the supporting rows underneath (Front-to-Back Runner Ratio, Front Bar Stitch Length, Back Bar Stitch Length, Fabric Produced per Rack and Combined Run-in) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Process planning — establishing Fabric Areal Weight before a trial is booked, so machine time and material in Advanced Knitting & Hosiery are committed against a calculated figure rather than an estimate.
- Costing and quotation — Fabric Areal Weight is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
- Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Front Bar Runner) shows how much of the gap in Fabric Areal Weight each variable explains.
- Teaching and study — the accepted ranges bracket normal Advanced Knitting & Hosiery practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.
Assumptions and limits
- Loom-state weight before relaxation and heat setting. A ratio far from the machine builder's window for the lapping usually shows up as barré or curling long before it shows up in the weight.
- Every input is bounded to the range normal practice occupies (Front Bar Runner 100 to 10000 mm/rack, Back Bar Runner 100 to 10000 mm/rack and Front Bar Yarn 10 to 5000 dtex, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
Questions people ask
What do I need to know before using the Warp Knit Rack Length & Two-Bar Run-in Ratio Calculator?
Have these to hand: Front Bar Runner, Back Bar Runner, Front Bar Yarn, Back Bar Yarn, Machine Gauge and Course Density. With those entered, the tool returns Fabric Areal Weight immediately.
What exactly is Fabric Areal Weight?
Both guide bars together, loom-state. It is reported in g/m². It is derived from Front Bar Runner, Back Bar Runner, Front Bar Yarn, Back Bar Yarn, Machine Gauge and Course Density, and is the figure the rest of the Advanced Knitting & Hosiery calculation is built around.
Which units does this calculator expect?
Enter Front Bar Runner in mm/rack, Back Bar Runner in mm/rack, Front Bar Yarn in dtex, Back Bar Yarn in dtex, Machine Gauge in needles/inch and Course Density in courses/cm. Mixing unit systems is the most common cause of a result that looks an order of magnitude wrong — convert before typing, not after reading.
What are the other figures under the main result?
They are the intermediate quantities the calculation passes through: Front-to-Back Runner Ratio, Front Bar Stitch Length, Back Bar Stitch Length, Fabric Produced per Rack and Combined Run-in. They are shown because a headline number nobody can trace is a number nobody trusts — checking them against your own expectation is the fastest way to confirm the inputs were read as you intended.
Can I rely on this for a production decision?
Loom-state weight before relaxation and heat setting. A ratio far from the machine builder's window for the lapping usually shows up as barré or curling long before it shows up in the weight. Treat the output as an engineering estimate that narrows the trial window, not as a substitute for the trial.