Textile Engineering
Finishing, Coating, Lamination & Functional Performance
13 interactive Finishing, Coating, Lamination & Functional Performance tools. Every one shows its formula, a worked example and the standards it follows.
Professional tools
Full costing sheets, booking schedules and project appraisals. Enter your own figures and see the headline result before you buy.
- Air, Sea or Split: Late Shipment Expedite Sheet Worth of Choosing Style by Style
- Brownfield Expansion: What the Next Increment Costs Shared Plant the Proposal Forces
- Built Into the Fibre or Applied to the Cloth: What Protection Costs Over a Life What Moving to the Cheapest Protection Saves
- Buyer Chargeback: Contest, Fix or Accept Recoverable a Year
- Buyer Cost to Serve & Development Recovery Net Margin After Serving the Book
- Buyer Quotation Generator Order Value
- Buyer Terms & Effective Price Comparison Best Offer, Once Its Terms Are Paid For
- Buyer Test Plan & Laboratory Budget Laboratory Cost for the Range
13
tools
Finishing & Environment
Finishing, Coating, Lamination & Functional Performance
Expand
Collapse
Finishing, Coating, Lamination & Functional Performance 13
- Which Finishing Line Each Quality Should Run On Premium Loads a book of fabric across finishing lines that are not the same as each other, by working out what a metre of each quality actually costs on each machine once width, chambers, hourly cost and the seconds that machine makes are all counted. Returns the metres to put on each line, what an extra ten hours on each is worth, and what loading by speed instead of by cost is costing. What Loading It Properly Is Worth cost
- Antimicrobial Log Reduction & Durable Dose Converts recovered colony counts into percentage and log reduction against the specification, shows the count a target log reduction actually demands, and carries the applied dose through wash retention to the initial loading a durable claim requires. Log Reduction log
- Dot Lamination Adhesive Add-On & Bonded Area Computes adhesive add-on from engraved dot geometry: cavity volume, volume per square metre, wet and dry add-on after transfer efficiency and solids, the share of area actually bonded, the finished laminate weight and the adhesive consumed per thousand metres. Dry Adhesive Add-On g/m2
- Finishing Trough Changeover: Purge Volume & Time Compares drain-and-refill cleaning against a continuous flow-through purge for a finishing trough, returning the rinse cycles a carryover limit needs, the volume and time each route costs and the water the better one saves. Drain-and-Refill Cycles Needed nos
- FR Add-On Durability & Initial Loading Required Treats flame retardant loss as geometric decay across launderings and returns the add-on surviving at the target wash count, the wash at which it crosses the effective minimum, the half-life of the finish and the initial loading a durable claim actually requires. Add-On at Target Wash Count % owf
- Heat-Setting Time-Temperature Equivalence & Line Speed Trade Converts a validated heat-setting reference of temperature and dwell into the equivalent dwell at any other temperature through the Arrhenius rate ratio, then into the line speed and production that temperature allows, with the degrees needed to buy a ten per cent speed change. Line Speed at the Proposed Temperature m/min
- Oil Repellency Grade from Critical Surface Tension Places a measured critical surface tension on the AATCC 118 test-liquid ladder to give the oil repellency grade achieved, the margin to the next rung, the critical tension a target grade demands and the Zisman contact angle at that liquid. Oil Repellency Grade AATCC
- Pad-Dry-Cure Thermal Load & Pick-Up Sensitivity Builds the full heat balance for a pad-dry-cure line: sensible heat in the carried water, latent heat of evaporation and sensible heat in the cloth to cure temperature, then the burner rating, the specific energy and what five points off the mangle would save. Burner Duty Required kW
- Raising Drum Kinematics & Pile Action Balance Turns drum and roller speeds into the surface speeds that matter, the slip between wire points and cloth for both pile and counter-pile rollers, the balance between them, and the relative travel a pass puts through the fabric. Pile Slip Speed m/min
- Sanforizing Compression from Belt Geometry Computes the surface strain a rubber belt develops around the compression roller, the compression actually applied at a given utilisation, the residual shrinkage that leaves, and the belt thickness or utilisation a target residual would require. Residual Shrinkage %
- Spray Rating Decay & Heat Reactivation Fits the per-wash decay of an AATCC 22 spray rating from a measured pair, projects the rating at the claimed wash count with and without heat reactivation, and reports the washes a target rating survives either way. Rating at the Claimed Wash Count AATCC
- Stenter Chain Width, Overfeed & Target GSM Solver Runs the stenter mass balance both ways: entry width, chain width, overfeed and finish add-on into the exit GSM they produce, and a target GSM back into the overfeed it demands - with the error against the current setting. Exit Fabric Weight g/m2
- Sueding Mass Loss, Strength Penalty & Fibre Cost Scales abrasive removal with grit number and contact intensity to give mass loss per pass and over a sequence, the finished GSM, the strength penalty that runs ahead of the weight loss, and the fibre being converted to dust every hour. Finished GSM g/m2
No calculator matches that search. Try a fibre, a machine, a unit or a standard.