Jump to a calculator 671 tools
Finishing & Environmental
Resin Finishing Add-on Percentage Calculator
Add-on is pick-up multiplied by concentration. Chasing crease recovery by raising both at once over-crosslinks the cotton.
Dry Resin Add-on
— % owf
Resin solids retained on the fabric
Batch Requirement
- Catalyst Add-on
- — % owf
- Total Chemical Add-on
- — % owf
- Resin Required
- — kg
- Liquor Required
- — L
Crosslinking buys crease recovery at the cost of tensile and tear strength. Confirm strength loss stays inside specification before raising add-on.
Using this calculator
About the Resin Finishing Add-on Percentage Calculator
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
resinAddOn = f( wetPickup, fabricWeight, resinConc, catalystConc )Each input feeds the expression evaluated in the browser; the symbol table below names every term and its unit.
| Symbol | Stands for | Unit |
|---|---|---|
wetPickup | Wet Pick-up | % |
fabricWeight | Fabric Batch Weight | kg |
resinConc | Resin Concentration | g/L |
catalystConc | Catalyst Concentration | g/L |
resinAddOn | Dry Resin Add-on | % owf |
catalystAddOn | Catalyst Add-on | % owf |
totalAddOn | Total Chemical Add-on | % owf |
resinRequired | Resin Required | kg |
liquorRequired | Liquor Required | L |
How the result is derived
Step by step, from the values you type to the figure on screen.
- The 4 inputs are read from the form on every keystroke: Wet Pick-up, Fabric Batch Weight, Resin Concentration and Catalyst Concentration.
- Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
- The validated values are substituted into the expression above, which resolves Dry Resin Add-on together with every supporting figure in one pass — no value is carried over from a previous entry.
- The supporting outputs — Catalyst Add-on, Total Chemical Add-on, Resin Required and Liquor Required — come from the same pass, so they always describe the same case as the headline figure.
- Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Wet Pick-up | % | 1 to 200 % | 70 | |
| Fabric Batch Weight | kg | 1 to 100000 kg | 1000 | |
| Resin Concentration | g/L | 1 to 500 g/L | 80 | |
| Catalyst Concentration | g/L | 0 to 200 g/L | 20 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Dry Resin Add-on (headline result) | % owf | Resin solids retained on the fabric |
| Catalyst Add-on | % owf | |
| Total Chemical Add-on | % owf | |
| Resin Required | kg | |
| Liquor Required | L |
Worked example
Given
- Wet Pick-up
- 70 %
- Fabric Batch Weight
- 1000 kg
- Resin Concentration
- 80 g/L
- Catalyst Concentration
- 20 g/L
The tool loads with this case already solved — the Dry Resin Add-on shown above is its answer. Change one value and the difference from this baseline is the sensitivity of the result to that variable.
How to use it
- Work through the input groups in order — Padder and Bath. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Dry Resin Add-on in the dark results panel — that is the headline figure, expressed in % owf.
- Check the supporting rows underneath (Catalyst Add-on, Total Chemical Add-on, Resin Required and Liquor Required) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Process planning — establishing Dry Resin Add-on before a trial is booked, so machine time and material in Finishing & Environmental Engineering are committed against a calculated figure rather than an estimate.
- Costing and quotation — Dry Resin Add-on is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
- Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Wet Pick-up) shows how much of the gap in Dry Resin Add-on each variable explains.
- Teaching and study — the accepted ranges bracket normal Finishing & Environmental Engineering practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.
Assumptions and limits
- Crosslinking buys crease recovery at the cost of tensile and tear strength. Confirm strength loss stays inside specification before raising add-on.
- Every input is bounded to the range normal practice occupies (Wet Pick-up 1 to 200 %, Fabric Batch Weight 1 to 100000 kg and Resin Concentration 1 to 500 g/L, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
On this site
Articles that explain what this tool calculates.
Questions people ask
What do I need to know before using the Resin Finishing Add-on Percentage Calculator?
Have these to hand: Wet Pick-up, Fabric Batch Weight, Resin Concentration and Catalyst Concentration. With those entered, the tool returns Dry Resin Add-on immediately.
What exactly is Dry Resin Add-on?
Resin solids retained on the fabric. It is reported in % owf. It is derived from Wet Pick-up, Fabric Batch Weight, Resin Concentration and Catalyst Concentration, and is the figure the rest of the Finishing & Environmental Engineering calculation is built around.
Which units does this calculator expect?
Enter Wet Pick-up in %, Fabric Batch Weight in kg, Resin Concentration in g/L and Catalyst Concentration in g/L. Mixing unit systems is the most common cause of a result that looks an order of magnitude wrong — convert before typing, not after reading.
What are the other figures under the main result?
They are the intermediate quantities the calculation passes through: Catalyst Add-on, Total Chemical Add-on, Resin Required and Liquor Required. They are shown because a headline number nobody can trace is a number nobody trusts — checking them against your own expectation is the fastest way to confirm the inputs were read as you intended.
Can I rely on this for a production decision?
Crosslinking buys crease recovery at the cost of tensile and tear strength. Confirm strength loss stays inside specification before raising add-on. Treat the output as an engineering estimate that narrows the trial window, not as a substitute for the trial.