Jump to a calculator 671 tools
Terry Weaving
Terry Towel Pile-to-Ground Ratio & GSM Calculator
Pile ratio is the towel. It sets absorbency, hand and roughly three quarters of the yarn cost, all from one let-off setting.
Towel Areal Weight
— g/m²
Loom-state weight of all three yarn streams
Weight Build-up
- Pile Warp Weight
- — g/m²
- Ground Warp Weight
- — g/m²
- Weft Weight
- — g/m²
- Pile Proportion of Weight
- — %
Warp Weight Split
—% pile warp —% ground warp
Loom-state weight. Terry gains weight per square metre in finishing as the cloth shrinks in both directions — apply your own finishing allowance before quoting a finished towel.
Using this calculator
About the Terry Towel Pile-to-Ground Ratio & GSM Calculator
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
pileGsm = pileEndsPerCm x 100 x pileRatio x pileYarnTex / 1000Ends per metre times the pile length fed per metre of cloth, times the yarn's grams per 1,000 m.
groundGsm = groundEndsPerCm x 100 x (1 + groundCrimp / 100) x groundYarnTex / 1000The weft term has the same form with picks per cm, weft crimp and weft tex.
totalGsm = pileGsm + groundGsm + weftGsm| Symbol | Stands for | Unit |
|---|---|---|
pileRatio | Pile Ratio | × |
pileEndsPerCm | Pile Ends per cm | ends/cm |
pileYarnTex | Pile Yarn Linear Density | tex |
groundEndsPerCm | Ground Ends per cm | ends/cm |
groundYarnTex | Ground Yarn Linear Density | tex |
groundCrimp | Ground Warp Crimp | % |
picksPerCm | Picks per cm | picks/cm |
weftYarnTex | Weft Yarn Linear Density | tex |
weftCrimp | Weft Crimp | % |
totalGsm | Towel Areal Weight | g/m² |
pileGsm | Pile Warp Weight | g/m² |
groundGsm | Ground Warp Weight | g/m² |
weftGsm | Weft Weight | g/m² |
pileProportion | Pile Proportion of Weight | % |
How the result is derived
Step by step, from the values you type to the figure on screen.
- The 9 inputs are read from the form on every keystroke: Pile Ratio, Pile Ends per cm, Pile Yarn Linear Density, Ground Ends per cm, Ground Yarn Linear Density, Ground Warp Crimp, Picks per cm, Weft Yarn Linear Density and Weft Crimp.
- Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
- The validated values are substituted into the expression above, which resolves Towel Areal Weight together with every supporting figure in one pass — no value is carried over from a previous entry.
- The supporting outputs — Pile Warp Weight, Ground Warp Weight, Weft Weight and Pile Proportion of Weight — come from the same pass, so they always describe the same case as the headline figure.
- Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Pile Ratio | × | 1 to 15 × | 5.5 | Pile warp length fed per unit of cloth woven. |
| Pile Ends per cm | ends/cm | 1 to 100 ends/cm | 12 | |
| Pile Yarn Linear Density | tex | 1 to 500 tex | 30 | |
| Ground Ends per cm | ends/cm | 1 to 100 ends/cm | 12 | |
| Ground Yarn Linear Density | tex | 1 to 500 tex | 20 | |
| Ground Warp Crimp | % | 0 to 40 % | 4 | |
| Picks per cm | picks/cm | 1 to 100 picks/cm | 16 | |
| Weft Yarn Linear Density | tex | 1 to 500 tex | 30 | |
| Weft Crimp | % | 0 to 40 % | 8 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Towel Areal Weight (headline result) | g/m² | Loom-state weight of all three yarn streams |
| Pile Warp Weight | g/m² | |
| Ground Warp Weight | g/m² | |
| Weft Weight | g/m² | |
| Pile Proportion of Weight | % |
Worked example
Given
- Pile
- 12 ends/cm, 30 tex, ratio 5.5
- Ground
- 12 ends/cm, 20 tex, 4% crimp
- Weft
- 16 picks/cm, 30 tex, 8% crimp
Substituting
pile = 1,200 x 5.5 m x 30 / 1000 = 198 g/m2ground = 1,200 x 1.04 x 20 / 1000 = 24.96 g/m2weft = 1,600 x 1.08 x 30 / 1000 = 51.84 g/m2total = 274.8 g/m2; pile share = 198 / 274.8 = 72.1 %Answer
- Towel
- 274.8 g/m²
- Pile
- 198 g/m² (72%)
- Ground
- 25.0 g/m²
- Weft
- 51.8 g/m²
Lowering the pile ratio to 4.5 cuts 36 g/m², to 238.8 g/m², with shorter loops.
How to use it
- Work through the input groups in order — Pile Warp, Ground Warp and Weft. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Towel Areal Weight in the dark results panel — that is the headline figure, expressed in g/m².
- Check the supporting rows underneath (Pile Warp Weight, Ground Warp Weight, Weft Weight and Pile Proportion of Weight) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Process planning — establishing Towel Areal Weight before a trial is booked, so machine time and material in Narrow Fabrics, Tapes & 3D Weaving are committed against a calculated figure rather than an estimate.
- Costing and quotation — Towel Areal Weight is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
- Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Pile Ratio) shows how much of the gap in Towel Areal Weight each variable explains.
- Teaching and study — the accepted ranges bracket normal Narrow Fabrics, Tapes & 3D Weaving practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.
Reading the result
Typical bands and what each one is telling you.
| Value | What it indicates |
|---|---|
| Towel too light | The pile ratio is the main lever; each point adds pile ends x pile tex grams. A heavier pile yarn does the same with the same loop height. |
| Pile share high | Most of the yarn cost and absorbency sit in the pile. The ground and weft hold the structure. |
| Finished towel heavier than loom state | Expected: terry shrinks in both directions in wet processing, so weight per m² rises. Apply your own finishing allowance. |
Assumptions and limits
- Loom-state weight. Terry gains weight per square metre in finishing as the cloth shrinks in both directions — apply your own finishing allowance before quoting a finished towel.
- Every input is bounded to the range normal practice occupies (Pile Ratio 1 to 15 ×, Pile Ends per cm 1 to 100 ends/cm and Pile Yarn Linear Density 1 to 500 tex, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
Standards and further reading
- ISO 3801 and ASTM D3776, mass per unit area of woven fabric, to weigh the towel against this estimate.
Questions people ask
How is the pile ratio measured?
Mark a length on the pile warp and on the cloth, weave, and divide the pile warp used by the cloth produced. Unravelling a loop sample gives the same figure.
Why is pile crimp not entered?
The pile ratio already includes all the length the pile end uses, loops and interlacing together.
Do two-sided towels need a different calculation?
No. Enter all pile ends, both faces together, in pile ends per cm.