Jump to a calculator 671 tools
Knitting
Knitted Fabric GSM Predictor
Knitted weight is loop count times loop length times linear density. Nothing else.
Predicted Fabric GSM
— g/m²
Relaxed knitted fabric weight
Loop Accounting
- Loops per Square Metre
- — no.
- Yarn per Square Metre
- — m
- Stitch Density
- — /cm2
- Yarn Linear Density
- — tex
Count CPI and WPI on a fully relaxed sample. Fabric measured straight off the machine will read low on courses and give a light GSM.
Using this calculator
About the Knitted Fabric GSM Predictor
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
loopsPerSqM = (cpi x 39.3701) x (wpi x 39.3701)Courses run across the fabric and wales run along it, so the loop count in a square metre is the product of the two densities converted to per-metre.
yarnLengthPerSqM = loopsPerSqM x stitchLength / 1000Stitch length is entered in millimetres, so dividing by 1000 puts the total into metres. This single input is the master variable of a knitted fabric — machine gauge and yarn count only set the range it can take.
tex = 590.5 / yarnNeGrams per 1000 metres. English count is indirect, so it divides.
gsm = yarnLengthPerSqM x tex / 1000Length times mass per unit length. Everything above exists to get those two numbers onto the same square metre.
stitchDensity = cpi x wpi / 6.45166.4516 is 2.54 squared — one square inch expressed in square centimetres.
| Symbol | Stands for | Unit |
|---|---|---|
cpi | Courses per Inch | CPI |
wpi | Wales per Inch | WPI |
stitchLength | Stitch Length | mm |
yarnNe | Yarn Count | Ne |
gsm | Predicted Fabric GSM | g/m² |
loopsPerSqM | Loops per Square Metre | no. |
yarnLengthPerSqM | Yarn per Square Metre | m |
stitchDensity | Stitch Density | /cm2 |
tex | Yarn Linear Density | tex |
How the result is derived
Step by step, from the values you type to the figure on screen.
- Courses and wales per inch are converted to per metre and multiplied, giving the number of loops the square metre contains.
- Every loop consumes exactly one stitch length of yarn, so total yarn length is a straight multiplication — no allowance for interlacing is needed because the loop path is the stitch length.
- The yarn count is converted to tex, which is grams per 1000 metres.
- Length in metres times tex, divided by 1000, gives grams per square metre.
- Stitch density is reported separately because it, not GSM, is what a knitter adjusts on the machine.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Courses per Inch | CPI | 1 to 200 CPI | 42 | |
| Wales per Inch | WPI | 1 to 200 WPI | 32 | |
| Stitch Length | mm | 0.5 to 15 mm | 2.9 | |
| Yarn Count | Ne | 1 to 200 Ne | 30 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Predicted Fabric GSM (headline result) | g/m² | Relaxed knitted fabric weight |
| Loops per Square Metre | no. | |
| Yarn per Square Metre | m | |
| Stitch Density | /cm2 | |
| Yarn Linear Density | tex |
Worked example
Given
- Courses per inch
- 42
- Wales per inch
- 32
- Stitch length
- 2.9 mm
- Yarn count
- 30 Ne
Substituting
loops = (42 x 39.3701) x (32 x 39.3701) = 1653.5 x 1259.8 = 2,083,204yarn = 2,083,204 x 2.9 / 1000 = 6,041.3 mtex = 590.5 / 30 = 19.68gsm = 6,041.3 x 19.68 / 1000 = 118.91 g/m2Answer
- Fabric GSM
- 118.91 g/m2
- Loops per square metre
- 2,083,204
- Yarn per square metre
- 6,041.29 m
- Stitch density
- 208.32 /cm2
- Yarn linear density
- 19.68 tex
A 30s single jersey at a normal loop length. Open the stitch length to 3.1 mm and GSM falls to about 111 — the same yarn, the same machine, a 6% lighter fabric.
How to use it
- Work through the input groups in order — Loop Density and Yarn & Loop. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Predicted Fabric GSM in the dark results panel — that is the headline figure, expressed in g/m².
- Check the supporting rows underneath (Loops per Square Metre, Yarn per Square Metre, Stitch Density and Yarn Linear Density) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Fabric development — hitting a buyer GSM by choosing the loop length, which is the one variable a knitter can set precisely and repeat.
- Yarn booking — kilograms per garment follow directly from GSM once the marker area is known.
- Machine setting and quality control — a GSM drift on the floor is nearly always a loop length drift; working the calculation backwards says how much.
- Costing a knit programme — comparing a heavier fabric at coarser count against a lighter one at finer count, on weight and on yarn price together.
Reading the result
Typical bands and what each one is telling you.
| Value | What it indicates |
|---|---|
| 100 to 130 g/m2 | Fine single jersey for lightweight tees and linings. |
| 140 to 180 g/m2 | Standard tee-shirt jersey — the commodity band. |
| 180 to 240 g/m2 | Heavy jersey, interlock, pique for polo shirts. |
| 250 to 350 g/m2 | Fleece and French terry before brushing. |
Assumptions and limits
- Count CPI and WPI on a fully relaxed sample. Fabric measured straight off the machine will read low on courses and give a light GSM.
- Every input is bounded to the range normal practice occupies (Courses per Inch 1 to 200 CPI, Wales per Inch 1 to 200 WPI and Stitch Length 0.5 to 15 mm, and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
Standards and further reading
- ASTM D3887 — tolerances for knitted fabrics, including mass per unit area.
- ISO 4921 — knitting vocabulary, which fixes what course, wale and stitch length mean.
- ISO 7211-2 / ASTM D3775 — thread density counting, the method behind the CPI and WPI inputs.
On this site
Articles that explain what this tool calculates.
Questions people ask
Why must the sample be relaxed before counting courses?
Fabric taken straight off the machine is still extended lengthwise. Counting on it under-reads courses per inch, and since GSM is proportional to that count, the prediction comes out light — commonly by 5% to 10%. Wet relax or dry relax the sample first, and state which, because the two give different numbers.
Where does stitch length come from if the fabric does not exist yet?
From the target GSM, working this calculation backwards, then checked against what the machine can hold: a rough guide for single jersey is a stitch length near 4.2 times the yarn diameter, and the achievable band narrows as gauge gets finer. Confirm it on the machine before booking yarn.
Does this cover interlock, rib and pique?
The loop accounting is general, but those structures have more than one loop system per course, so the effective loops per square metre and the stitch length differ from the plain single jersey case. Enter the measured course and wale density of the actual structure and the arithmetic holds.