Jump to a calculator 671 tools
Knitting
Circular Knitting Production Calculator
Knitting output is set by loops per minute and stitch length, not by machine diameter.
Fabric per Shift
— kg
One machine at the stated efficiency
Production Rates
- Machine Output
- — kg/h
- Yarn Consumed
- — m/h
- Courses Knitted
- — /min
- Loops Formed
- — /min
Stitch length is the single biggest lever here and the one most often drifting. Check it on the machine with a course-length counter, not from the pattern sheet.
Using this calculator
About the Circular Knitting Production Calculator
The formula
This is the expression the tool evaluates. Every term is named underneath, with the unit it must be supplied in.
kgPerShift = f( rpm, feeders, needles, stitchLength, yarnNe, efficiency, shiftHours )Each input feeds the expression evaluated in the browser; the symbol table below names every term and its unit.
| Symbol | Stands for | Unit |
|---|---|---|
rpm | Cylinder Speed | rpm |
feeders | Feeders | no. |
needles | Needles in Cylinder | no. |
stitchLength | Stitch Length | mm |
yarnNe | Yarn Count | Ne |
efficiency | Machine Efficiency | % |
shiftHours | Shift Length | h |
kgPerShift | Fabric per Shift | kg |
kgPerHour | Machine Output | kg/h |
yarnLengthPerHour | Yarn Consumed | m/h |
coursesPerMinute | Courses Knitted | /min |
loopsPerMinute | Loops Formed | /min |
How the result is derived
Step by step, from the values you type to the figure on screen.
- The 7 inputs are read from the form on every keystroke: Cylinder Speed, Feeders, Needles in Cylinder, Stitch Length, Yarn Count, Machine Efficiency and Shift Length.
- Each value is checked against the accepted range in the input table below. A value outside its range stops the calculation rather than producing a misleading figure — the results blank out and a message appears.
- The validated values are substituted into the expression above, which resolves Fabric per Shift together with every supporting figure in one pass — no value is carried over from a previous entry.
- The supporting outputs — Machine Output, Yarn Consumed, Courses Knitted and Loops Formed — come from the same pass, so they always describe the same case as the headline figure.
- Results are rounded for display only. The full-precision value is used throughout the chain, so reading a rounded intermediate figure back into the tool by hand can shift the last digit.
What each input means
Where to read each value on the floor, the unit it must be in, and the range the tool accepts.
| Input | Unit | Accepted range | Default | What it means |
|---|---|---|---|---|
| Cylinder Speed | rpm | 1 to 100 rpm | 25 | |
| Feeders | no. | 1 to 300 no. | 96 | |
| Needles in Cylinder | no. | 1 to 10000 no. | 2400 | |
| Stitch Length | mm | 0.5 to 15 mm | 2.9 | |
| Yarn Count | Ne | 1 to 200 Ne | 30 | |
| Machine Efficiency | % | 30 to 100 % | 90 | |
| Shift Length | h | 1 to 24 h | 8 |
What the tool returns
The headline figure and every supporting value it is built from.
| Output | Unit | What it tells you |
|---|---|---|
| Fabric per Shift (headline result) | kg | One machine at the stated efficiency |
| Machine Output | kg/h | |
| Yarn Consumed | m/h | |
| Courses Knitted | /min | |
| Loops Formed | /min |
Worked example
Given
- Cylinder Speed
- 25 rpm
- Feeders
- 96 no.
- Needles in Cylinder
- 2400 no.
- Stitch Length
- 2.9 mm
- Yarn Count
- 30 Ne
- Machine Efficiency
- 90 %
- Shift Length
- 8 h
The tool loads with this case already solved — the Fabric per Shift shown above is its answer. Change one value and the difference from this baseline is the sensitivity of the result to that variable.
How to use it
- Work through the input groups in order — Machine and Fabric & Shift. The defaults are a realistic case, so you can change one value at a time and watch what moves.
- There is no calculate button. Every figure recalculates as you type or drag, which is what makes this usable for a what-if sweep rather than a single answer.
- Read Fabric per Shift in the dark results panel — that is the headline figure, expressed in kg.
- Check the supporting rows underneath (Machine Output, Yarn Consumed, Courses Knitted and Loops Formed) before acting on the headline — they are where an implausible input usually shows itself first.
- Reset to defaults returns every field to the reference case, which is the quickest way to check whether a surprising result came from the tool or from an input you had changed earlier.
Where this is used
- Process planning — establishing Fabric per Shift before a trial is booked, so machine time and material in Knitting are committed against a calculated figure rather than an estimate.
- Costing and quotation — Fabric per Shift is an input to the cost sheet, and quoting from a worked number rather than a remembered one is what keeps a margin intact.
- Troubleshooting — when the floor result drifts from plan, entering the measured values (starting with Cylinder Speed) shows how much of the gap in Fabric per Shift each variable explains.
- Teaching and study — the accepted ranges bracket normal Knitting practice, so moving one variable at a time shows the shape of the relationship rather than a single answer.
Assumptions and limits
- Stitch length is the single biggest lever here and the one most often drifting. Check it on the machine with a course-length counter, not from the pattern sheet.
- Every input is bounded to the range normal practice occupies (Cylinder Speed 1 to 100 rpm, Feeders 1 to 300 no. and Needles in Cylinder 1 to 10000 no., and so on for the rest). Those bounds are guard rails against typing errors, not a claim that the formula fails one unit outside them.
- The calculation is deterministic: the same inputs always give the same result. It carries no allowance for machine condition, operator skill, ambient conditions or lot-to-lot material variation unless an input above explicitly represents one.
- Nothing is sent anywhere. The maths runs in your browser, so the numbers you type never leave the page.
On this site
Articles that explain what this tool calculates.
Questions people ask
What do I need to know before using the Circular Knitting Production Calculator?
Have these to hand: Cylinder Speed, Feeders, Needles in Cylinder, Stitch Length, Yarn Count, Machine Efficiency and Shift Length. With those entered, the tool returns Fabric per Shift immediately.
What exactly is Fabric per Shift?
One machine at the stated efficiency. It is reported in kg. It is derived from Cylinder Speed, Feeders, Needles in Cylinder, Stitch Length, Yarn Count, Machine Efficiency and Shift Length, and is the figure the rest of the Knitting calculation is built around.
Which units does this calculator expect?
Enter Cylinder Speed in rpm, Feeders in no., Needles in Cylinder in no., Stitch Length in mm, Yarn Count in Ne, Machine Efficiency in % and Shift Length in h. Mixing unit systems is the most common cause of a result that looks an order of magnitude wrong — convert before typing, not after reading.
What are the other figures under the main result?
They are the intermediate quantities the calculation passes through: Machine Output, Yarn Consumed, Courses Knitted and Loops Formed. They are shown because a headline number nobody can trace is a number nobody trusts — checking them against your own expectation is the fastest way to confirm the inputs were read as you intended.
Can I rely on this for a production decision?
Stitch length is the single biggest lever here and the one most often drifting. Check it on the machine with a course-length counter, not from the pattern sheet. Treat the output as an engineering estimate that narrows the trial window, not as a substitute for the trial.