Rieter K 48 is a ring spinning frame, still in its builder’s current range. Its builder lists spindle speed mechanical up to 28 000 rpm, machine width with ROBOspin 1 586 mm and depending on spindle number 55 kW. It draws roving down to its final count and inserts twist through a traveller running on a ring, winding the yarn onto cops.
Ring spinning frameSpinningIn the builder's current range
Key specifications
3 of 4 key figures recorded
- Make
RieterSwitzerlandrieter.com (the builder's website, opens in a new tab) All 68 machines from Rieter - Class
- Ring spinning frame
- Process stage
- Spinning
- Lifecycle
- In the builder's current range
- Standards
- Safety ISO 11111-2 Noise ISO 9902-2
Specification
| Parameter | Value | Comparable |
|---|---|---|
| Spindle speed Mechanical | up to 28 000 rpm | |
| depending on spindle number | 55 kW | |
| Drafting system drive (Standard) | 5 – 17.5 kW | |
| Without IMD | 4.4 – 8.8 kW | |
| VARIOspin | 4.4 – 15.6 kW | |
| Ring rail drive | 1.75 kW | |
| Single-sided suction with frequency converter | Up to 960 spindles 6.5 kW | |
| Double-sided suction with frequency converter | 1 296 – 1 824 spindles 2 x 6.5 kW | |
| Rated voltage | 380 – 440 V; 50/60 Hz | |
| Min. supply pressure | 7 bar | |
| Consumption | approx. 1.5 Nm3/h (up to 1 440 spindles) | |
| Material Cotton ≥ | 27 mm (1 1/16 in); | |
| Man-made fibers and blends | up to 51 mm (2 in) | |
| Standard Cotton | 29.5 – 3.7 tex | |
| Optional Cotton | 29.5 – 2.4 tex | |
| Twist range | 200 – 3 000 T/m (5.1 – 76.1 T/in) | |
| Draft (Standard) | 8 – 130 fold (mechanical) | 1:8–1:130 |
| Number of spindles (gauge | 70/75 mm) | |
| Per section | 48 | |
| Spindle gauge | 70; 75 mm | |
| Ring diameter | 70-mm gauge 34; 36; 38; 40; 42; 45 mm | 34–70 mm |
| Tube length | 70-mm gauge 180 – 230 mm | |
| DUI | 16 LENA 28 spindle with 34 mm ring | |
| Over center of spindle | 660 mm | |
| Doffer retracted | 1 062 mm | |
| Doffer extended | 1 380 mm | |
| Machine width with ROBOspin | 1 586 mm | |
| Installed power | 2 x 0.48 kW |
Read from the builder's published page: www.rieter.com, on 2026-08-22.
Standards that apply to this class
Machines of this class fall under the textile machinery standards for spinning preparatory and spinning machines. The common requirements of ISO 11111-1 apply to every machine in this family.
- Safety
- ISO 11111-2 Textile machinery — Safety requirements — Part 2: Spinning preparatory and spinning machines — Amendment 1
- Noise
- ISO 9902-2 Textile machinery — Noise test code — Part 2: Spinning preparatory and spinning machinery
These standards cover the class of machine, not this model. A machine's own declaration of conformity says which editions it was built to.
Run this machine
- Production of this frame carries Number of spindles (gauge
- End breakage at this speed carries Number of spindles (gauge, Spindle speed Mechanical
- Suction energy on this frame carries Number of spindles (gauge
The figures carried across are the builder's maxima — what the machine was built to reach, not what a mill runs it at. The gap between the two is most of the difference between a nameplate and a shift report, so replace them with what your own machine actually does before you believe the answer.
Check against the machine before you buy or budget on it. Builders publish a range and a configuration; the machine on your floor may be a different variant, may have been rebuilt, and may not carry the options these figures assume. This register records what the builder published, not what any individual machine does.
The record
- Read from
- www.rieter.com,
- Archived copy
- snapshot, captured 2026-08-22
- Checked by
- Textile School,
- Last changed
Related machines
Other machines of this kind: Ring spinning frame
Report incorrect information on this page
Tell us what is wrong and we will check it against the source. Reports are private, are never published, and go to an editor rather than into a comment thread.